The Sonoff MINI-ZBRBS is a smart switch for shutters and curtains that uses the Zigbee 3.0 protocol. Designed to offer comfort and precision, it allows you to upgrade traditional motors to smart systems without requiring replacement of existing equipment. Thanks to its ultra-slim design, it easily fits into most European wall electrical boxes (type 60/80), providing a discreet and powerful automation solution for your home.
Local Control and Network Enhancement
The device harnesses the power of Zigbee to execute local scenes. This means that, once configured through a compatible hub, automations are carried out instantly within the home network, even if the internet connection is interrupted. Additionally, the MINI-ZBRBS operates as a Zigbee Router (signal repeater), helping to extend the range and improve the stability of your entire smart network.
Precision and Customization
The switch supports position control based on percentage, allowing you to open or close the shutters exactly to the level you desire. Through the calibration function, the device learns the limits of the motor's movement, ensuring smooth operation and protecting the mechanism from wear. It is fully compatible with third-party platforms such as Home Assistant, and also supports the connection of physical switches for manual control at any time.
Specifications
Model: MINI-ZBRBS
Product type: Zigbee smart roller switch
Input voltage: 100-240V ~ 50/60Hz
Maximum load: 1A (approximately 100-240W depending on voltage)
Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.
I have 6 of these at my home in Home Assistant via z2m. I had bought 12, 3 of them were DOA. They work ok BUT for some reason if the physical switch is pressed (which works normally and automatically updates the % open status of the roller in HA) they disconnect. And I have to open the wall switch, press the reset, and then they work normally again. All 6 that I have have done this at least once. So as long as they work, they're ok but overall very poor quality.
Έχω 6 τέτοια στο σπίτι μου σε home assistant μέσω z2m. Είχα πάρει 12, τα 3 ήταν dof. Λειτουργούν οκ ΑΛΛΑ για κάποιο λόγο αν πατηθεί ο φυσικός διακόπτης (που λειτουργεί κανονικά και ανανεώνει αυτόματα το πóσο ανοιχτό % είναι το ρόλο στο ha) αποσυνδέονται. Και πρέπει να ανοίξω τον διακόπτη του τοίχου, να πατήσω το reset και ξανά δουλεύουν κανονικά. Το έχουν κάνει και τα 6 που εχω από μια φορά τουλάχιστον. Οπότε όσο δουλευουν ειναι οκ αλλά πολύ κακής ποιότητας γενικά.
If it is connected with Home Assistant, the calibration must be done manually from the device and not from any application. It works perfectly in Home Assistant with z2m
Αμα μπει με home assistant το calibration πρέπει να γίνει χειροκίνητα από την συσκευή και όχι από κάποια εφαρμογή. Δουλεύει άψογα σε home assistant με z2m
I have 6 of these at my home in Home Assistant via z2m. I had bought 12, 3 of them were DOA. They work ok BUT for some reason if the physical switch is pressed (which works normally and automatically updates the % open status of the roller in HA) they disconnect. And I have to open the wall switch, press the reset, and then they work normally again. All 6 that I have have done this at least once. So as long as they work, they're ok but overall very poor quality.
Έχω 6 τέτοια στο σπίτι μου σε home assistant μέσω z2m. Είχα πάρει 12, τα 3 ήταν dof. Λειτουργούν οκ ΑΛΛΑ για κάποιο λόγο αν πατηθεί ο φυσικός διακόπτης (που λειτουργεί κανονικά και ανανεώνει αυτόματα το πóσο ανοιχτό % είναι το ρόλο στο ha) αποσυνδέονται. Και πρέπει να ανοίξω τον διακόπτη του τοίχου, να πατήσω το reset και ξανά δουλεύουν κανονικά. Το έχουν κάνει και τα 6 που εχω από μια φορά τουλάχιστον. Οπότε όσο δουλευουν ειναι οκ αλλά πολύ κακής ποιότητας γενικά.
If it is connected with Home Assistant, the calibration must be done manually from the device and not from any application. It works perfectly in Home Assistant with z2m
Αμα μπει με home assistant το calibration πρέπει να γίνει χειροκίνητα από την συσκευή και όχι από κάποια εφαρμογή. Δουλεύει άψογα σε home assistant με z2m
The Sonoff MINI-ZBRBS is a smart switch for shutters and curtains that uses the Zigbee 3.0 protocol. Designed to offer comfort and precision, it allows you to upgrade traditional motors to smart systems without requiring replacement of existing equipment. Thanks to its ultra-slim design, it easily fits into most European wall electrical boxes (type 60/80), providing a discreet and powerful automation solution for your home.
Local Control and Network Enhancement
The device harnesses the power of Zigbee to execute local scenes. This means that, once configured through a compatible hub, automations are carried out instantly within the home network, even if the internet connection is interrupted. Additionally, the MINI-ZBRBS operates as a Zigbee Router (signal repeater), helping to extend the range and improve the stability of your entire smart network.
Precision and Customization
The switch supports position control based on percentage, allowing you to open or close the shutters exactly to the level you desire. Through the calibration function, the device learns the limits of the motor's movement, ensuring smooth operation and protecting the mechanism from wear. It is fully compatible with third-party platforms such as Home Assistant, and also supports the connection of physical switches for manual control at any time.
Specifications
Model: MINI-ZBRBS
Product type: Zigbee smart roller switch
Input voltage: 100-240V ~ 50/60Hz
Maximum load: 1A (approximately 100-240W depending on voltage)
Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.
I have 6 of these at my home in Home Assistant via z2m. I had bought 12, 3 of them were DOA. They work ok BUT for some reason if the physical switch is pressed (which works normally and automatically updates the % open status of the roller in HA) they disconnect. And I have to open the wall switch, press the reset, and then they work normally again. All 6 that I have have done this at least once. So as long as they work, they're ok but overall very poor quality.
Έχω 6 τέτοια στο σπίτι μου σε home assistant μέσω z2m. Είχα πάρει 12, τα 3 ήταν dof. Λειτουργούν οκ ΑΛΛΑ για κάποιο λόγο αν πατηθεί ο φυσικός διακόπτης (που λειτουργεί κανονικά και ανανεώνει αυτόματα το πóσο ανοιχτό % είναι το ρόλο στο ha) αποσυνδέονται. Και πρέπει να ανοίξω τον διακόπτη του τοίχου, να πατήσω το reset και ξανά δουλεύουν κανονικά. Το έχουν κάνει και τα 6 που εχω από μια φορά τουλάχιστον. Οπότε όσο δουλευουν ειναι οκ αλλά πολύ κακής ποιότητας γενικά.
If it is connected with Home Assistant, the calibration must be done manually from the device and not from any application. It works perfectly in Home Assistant with z2m
Αμα μπει με home assistant το calibration πρέπει να γίνει χειροκίνητα από την συσκευή και όχι από κάποια εφαρμογή. Δουλεύει άψογα σε home assistant με z2m
I have 6 of these at my home in Home Assistant via z2m. I had bought 12, 3 of them were DOA. They work ok BUT for some reason if the physical switch is pressed (which works normally and automatically updates the % open status of the roller in HA) they disconnect. And I have to open the wall switch, press the reset, and then they work normally again. All 6 that I have have done this at least once. So as long as they work, they're ok but overall very poor quality.
Έχω 6 τέτοια στο σπίτι μου σε home assistant μέσω z2m. Είχα πάρει 12, τα 3 ήταν dof. Λειτουργούν οκ ΑΛΛΑ για κάποιο λόγο αν πατηθεί ο φυσικός διακόπτης (που λειτουργεί κανονικά και ανανεώνει αυτόματα το πóσο ανοιχτό % είναι το ρόλο στο ha) αποσυνδέονται. Και πρέπει να ανοίξω τον διακόπτη του τοίχου, να πατήσω το reset και ξανά δουλεύουν κανονικά. Το έχουν κάνει και τα 6 που εχω από μια φορά τουλάχιστον. Οπότε όσο δουλευουν ειναι οκ αλλά πολύ κακής ποιότητας γενικά.
If it is connected with Home Assistant, the calibration must be done manually from the device and not from any application. It works perfectly in Home Assistant with z2m
Αμα μπει με home assistant το calibration πρέπει να γίνει χειροκίνητα από την συσκευή και όχι από κάποια εφαρμογή. Δουλεύει άψογα σε home assistant με z2m